Maytag appliance troubleshooting
Browse Maytag appliance symptoms and codes. Similar characters can have different meanings across appliance types.
MEDC465HW keeps tumbling after the cycle ends
Maytag’s MEDC465HW feature sheet describes Wrinkle Control as 40 minutes of additional no-heat tumbling after drying.
Follow the checksMVWC565FW2 stuck on sensing or not filling
The MVWC565FW2 manual describes Auto Sensing as a fill-and-sense sequence that pauses when an unlocked lid is opened.
Follow the checksMVW4505MW will not start: the Start/Pause gesture
The MVW4505MW quick-start guide calls for holding Start/Pause for 1 second until all status lights illuminate, then releasing.
Follow the checksMaytag top-load spin and balance troubleshooting
Separate water that will not drain from a basket that cannot complete spin.
Follow the checksMaytag dishwasher not filling: control or water path?
Maytag lists door closure, supply availability and an obstructed overfill float among checks for a dishwasher that will not fill.
Follow the checksMHW5630HW Control Lock Will Not Clear: Watch the Countdown
Hold the Control Lock control continuously for three seconds.
Follow the checksMHW6630HW Door Locked After Washing: Check Fresh Hold
The MHW6630HW has a 16-hour Fresh Hold option.
Follow the checksMVW6230HW Deep Fill: Auto, Medium, High and Max Compared
MVW6230HW provides Auto, Medium, High and Max Fill choices.
Follow the checksMVW6500MW Pet Pro Filter Not Catching Hair
On the MVW6500MW, select Pet Pro and start with a clean filter.
Follow the checksMHW8630HW Optimal Dose: Detergent Settings Before Service
The MHW8630HW Optimal Dose system meters liquid HE detergent from a reservoir.
Follow the checksMaytag F9 E1 With a Clean Filter: Inspect the Drain Path
F9 E1 reports a long-drain problem.
Follow the checksMaytag Sd Keeps Adding Rinses: Let the Suds Routine Finish
On the covered Maytag front-load washers, Sd or Sud means excess suds.
Follow the checksMaytag Int and a Locked Door After Canceling
Int indicates a paused or canceled cycle.
Follow the checksMaytag rL or F0 E7 During Clean Washer: Remove the Load
Maytag documents rL/F34 and, on other supported platforms, F0 E7 as clothing detected during Clean Washer.
Follow the checksMaytag Dryer L2 but the Drum Still Runs
Maytag says L2 can indicate low or missing supply voltage that prevents heating while the drum continues running.
Follow the checksMaytag Dryer AF After Cleaning: Check the Whole Exhaust Path
AF or Check Vent concerns restricted airflow.
Follow the checksMaytag Dryer PF After an Outage: Resume or Investigate?
PF indicates that a power failure interrupted drying.
Follow the checksMaytag Dryer F3 E2: Moisture Sensing, Not a Washer Code
For the dryer support page cited here, Maytag identifies F3 E2 with moisture sensing.
Follow the checksMaytag F0 E5 Returns After Redistributing the Load
F0 E5 means the load is unbalanced or too large on the covered top-load washers.
Follow the checksMaytag F5 E3 and a Lid That Will Not Unlock
Maytag identifies F5 E3 as a lock-related alert on covered top-load washers.
Follow the checksMaytag F7 E1: Identify the Washer Platform Before Parts
F7 E1 is a speed-related fault, but the relevant system depends on the washer platform.
Follow the checksMaytag F8 E6: Hot-Water Fault or Open Lid During Soak?
Maytag explicitly publishes two possible F8 E6 meanings depending on model: an open lid during soak, or no hot water detected.
Follow the checksMVWC465HW1 Deep Water Wash: Check the Water Level Knob
The MVWC465HW1 owner guide directs owners to the Water Level knob’s Deep Water Wash setting for more water.
Follow the checksMEDB835DW Sensor Dry: Change the Saved Dryness Setting
MEDB835DW supports a saved Sensor Cycle dryness adjustment from standby.
Follow the checksMVW5430MW Fabric Softener: Select an Extra Rinse Setting
The MVW5430MW quick-start guide says to use one of the two topmost Soil & Rinse settings when using fabric softener; those settings add an Extra Rinse.
Follow the checksMED7230HW Steam Refresh Leaves Wet Spots
Steam Refresh on MED7230HW is intended to refresh dry garments, not to dry a wet washer load.
Follow the checksMED6500MW Pet Pro Runs Without Heat: What Is Normal?
The MED6500MW Pet Pro option deliberately uses an extended no-heat period to lift hair into its XL lint trap.
Follow the checksMED6230HW Connects to the App but Will Not Start Remotely
Connecting MED6230HW to the app and authorizing remote control are separate steps.
Follow the checksMVW7230HW Rinse and Spin: Use Drain & Spin Plus Extra Rinse
For a Rinse & Spin on MVW7230HW, the quick-reference guide says to select Drain & Spin, then select Extra Rinse.
Follow the checksMVWB765FW Clean Washer Was Interrupted: Rinse Before Laundry
The MVWB765FW guide says not to interrupt Clean Washer.
Follow the checks