Samsung washers troubleshooting
Use the symptom or code to choose a safe starting point for Samsung washers. Verify the exact model before maintenance.
Start with the water, then the spin.
Look for standing water, a displayed code and whether the cycle completed. A drain fault, imbalance and reduced spin setting can all leave wet clothes for different reasons.
WA45H7000AW/A2 4E: fill error and recall check
The WA45H7000AW/A2 manual defines 4E as a fill failure, not imbalance.
Follow the checksSamsung washer 4C even with both taps open
Open valves do not establish correct incoming flow or the entire installation.
Follow the checksSamsung washer 5C after the filter was cleaned
If 5C remains after permitted user-filter cleaning, record the accessible areas actually checked and whether the household drain backs up.
Follow the checksSamsung Ur keeps adding time: retry or failure?
Ur can report a balance retry rather than a failed part.
Follow the checksSamsung washer 4C2 after supply-hose work
After hose or plumbing work, 4C2 needs a hot/cold supply-identification check.
Follow the checksWF45R6100AW Spin Only: Avoid Starting Another Rinse
Hold Spin for three seconds to select Spin Only.
Follow the checksWF45R6100AW Child Lock Flashes: Temporary Off or Fully Off?
Use Temp.
Follow the checksWF45R6100AW Delay End: Why the Wash Does Not Start Immediately
Delay End schedules completion, rather than a delay before starting of the same length.
Follow the checksWF45T6000AW Self Clean Light Blinks After Washing
The Self Clean reminder appears after 40 wash cycles on the cited WF45T6000A manual.
Follow the checksWF45T6000AW Emergency Drain: Tube Before Pump Filter
The model has an emergency drain tube at the lower front access area.
Follow the checksWF50A8800AV Does Not Dispense on Delicates: Check Dose per Wash
Check Dose per Wash and Dose per Rinse after selecting the cycle.
Follow the checksWF50A8800AV Missing a Wash Cycle? Check My Cycles
The displayed cycle list can be personalized through My Cycles.
Follow the checksWF50A8800AV Calibration Is in System Functions
For the cited model, hold Options for three seconds, select Calibration with the Navigation dial and confirm with OK.
Follow the checksWA50R5400AW Waterjet Stops and Power Waits During Drain
Active Waterjet stops automatically after five minutes on the cited manual.
Follow the checksWF45K6500AV AddWash Will Not Open During a Hot Cycle
Pause only when the Add Wash indication permits adding laundry.
Follow the checksWF45A6400AW Door Stays Locked After a Cycle: Stay Connect
Check whether Stay Connect is active in SmartThings.
Follow the checksWV60M9900AV Upper Washer 1dC4: Inspect the Latch Button
On FlexWash, Samsung identifies a missing rubber button beside the upper washer latch as a cause of 1dC4.
Follow the checksWA55A7700AV Recall Software: Check the Remedy Before Washing
Check both model and serial number against the recall, then verify the installed software using Samsung’s current remedy instructions.
Follow the checksSamsung ddC or dC3 After Adding Laundry
ddC/dC3 concerns the Add Door, not a drain filter.
Follow the checksSamsung SDC/5DC With the Detergent Drawer Closed
SDC/5DC means the detergent drawer is not confirmed completely closed.
Follow the checksSamsung dn and Frozen Controls During an Update
dn is a software-download status.
Follow the checksSamsung CL After Opening the Lid: Why Water Drained
On covered newer washers, CL can identify a Child Lock protective drain after the lid or door was opened with an unsafe water level.
Follow the checksSamsung PC Versus PC1: Clutch Position or Signal?
PC/PE concerns clutch position; PC1/PE1 concerns the clutch Hall signal.
Follow the checksSamsung 3C With No Drum Rotation: What the Code Establishes
3C belongs to the motor-error family in Samsung’s reference.
Follow the checksSamsung AC6 After a Power Event: Preserve the Fault Details
AC6 is a communication error in Samsung’s code reference.
Follow the checksSamsung 8C After Moving: Sensor Fault or Ordinary Imbalance?
Samsung groups 8C with MEMS-sensor errors.
Follow the checksSamsung 9C1 After an Outage: Power Check Before Another Wash
Samsung groups 9C1/9C2 and PF with supply-voltage problems.
Follow the checksSamsung SUD With No Visible Foam: Record What Happens Next
SUD is an oversudsing indication, not a direct instruction to replace a sensor.
Follow the checksSamsung Washer LC With No Visible Leak: Do Not Assume It Is Dry
Samsung’s LC/LE/1C family can concern water level or leakage.
Follow the checksSamsung OC and Water Entering While Off: Stop the Supply
OC/OE is an overflow code family.
Follow the checks