Washers troubleshooting
Look for standing water, a displayed code and whether the cycle completed. A drain fault, imbalance and reduced spin setting can all leave wet clothes for different reasons.
Start with the water, then the spin.
Look for standing water, a displayed code and whether the cycle completed. A drain fault, imbalance and reduced spin setting can all leave wet clothes for different reasons.
WFC7500VW A10: compact-washer drain checks
Whirlpool’s WFC7500VW compact washer guidance identifies A10 as a drain problem.
Follow the checksMVWC565FW2 stuck on sensing or not filling
The MVWC565FW2 manual describes Auto Sensing as a fill-and-sense sequence that pauses when an unlocked lid is opened.
Follow the checksMVW4505MW will not start: the Start/Pause gesture
The MVW4505MW quick-start guide calls for holding Start/Pause for 1 second until all status lights illuminate, then releasing.
Follow the checksWM3400CW OE: residual-water hose and drain filter
The WM3400CW manual identifies a residual-water drain hose and drain-pump filter behind its maintenance cover.
Follow the checksWM4000HWA CL: Rinse+Spin versus Control Lock
In the matched WM4000HWA manual, holding Rinse+Spin for 3 seconds toggles Control Lock; a short press selects a different function.
Follow the checksWT7300CW Spin Only adds water: check the selection
The WT7300CW manual selects Spin Only by holding Spin for 3 seconds; Rinse+Spin is a separate Special Care selection.
Follow the checksWA45H7000AW/A2 4E: fill error and recall check
The WA45H7000AW/A2 manual defines 4E as a fill failure, not imbalance.
Follow the checksWhirlpool F9 E1 with a clean drain filter
A clean user filter does not verify the hose, standpipe or pump.
Follow the checksWhirlpool F8 E1: door locked and pump running
Whirlpool documents a protective drain routine with temporarily unresponsive controls after F8 E1/Lo FL.
Follow the checksWhirlpool front-load F5 E2 although the door closes
A door that physically closes is not the same as confirmation that the lock circuit recognizes it.
Follow the checksWhirlpool Sud or Sd after a detergent change
A change in detergent concentration can make the old measuring habit inappropriate.
Follow the checksSamsung washer 4C even with both taps open
Open valves do not establish correct incoming flow or the entire installation.
Follow the checksSamsung washer 5C after the filter was cleaned
If 5C remains after permitted user-filter cleaning, record the accessible areas actually checked and whether the household drain backs up.
Follow the checksSamsung Ur keeps adding time: retry or failure?
Ur can report a balance retry rather than a failed part.
Follow the checksSamsung washer 4C2 after supply-hose work
After hose or plumbing work, 4C2 needs a hot/cold supply-identification check.
Follow the checksLG front-load OE with a clear drain filter
OE can remain after filter cleaning because the filter is only one point in the drain path.
Follow the checksLG front-load UE on a small load
A small load can still distribute poorly.
Follow the checksLG washer IE after a water shutoff
If IE began after a household shutoff or plumbing work, start with supply availability and safely visible hose routing.
Follow the checksLG washer CL stays on after the cycle
A completed wash does not automatically disable Child Lock.
Follow the checksWhirlpool front-load wet clothes: drain, foam or spin?
Wet clothes after a completed front-load cycle can reflect spin settings, an unbalanced load, excess suds or drainage trouble.
Follow the checksMaytag top-load spin and balance troubleshooting
Separate water that will not drain from a basket that cannot complete spin.
Follow the checksWTW5057LW Fabric Softener: Which Option and Where It Goes
The Fabric Softener button changes the rinse; it does not identify a built-in softener dispenser.
Follow the checksWTW5057LW Will Not Start: Hold, Watch the Lights, Then Release
Hold Start/Pause for one second until the status lights illuminate, then release.
Follow the checksWTW5057LW With the Agitator Removed: What Changes
Removing the designed removable post changes this washer to impeller mode.
Follow the checksWTW5057LW Has No Temperature Light: Check Tap Cold
No illuminated light in the temperature column can mean Tap Cold is selected.
Follow the checksWTW8127LW Load & Go: Switch to a Single Detergent Dose
Choose the Load & Go dispensing option deliberately before adding a single detergent dose.
Follow the checksWTW8127LW Faucet Water Drains During Soaking
Water added with the pretreat faucet can drain automatically if the lid stays open for ten minutes or the water level becomes too high.
Follow the checksWTW8127LW Remote Start Stops Working After Opening the Lid
Opening the lid cancels Remote Enable.
Follow the checksWFW3090JW Dosing Aid Shows a Number but Does Not Add Detergent
Dosing Aid calculates a recommended detergent quantity in milliliters.
Follow the checksWFW3090JW and Chlorine Bleach: Follow This Model’s Restriction
The WFW3090JW manual says not to use chlorine bleach.
Follow the checksWFW5090JW “Clean Filter”: Follow the Whole Drain Path
Clean Filter on this compact washer is a drainage warning, not proof that the removable filter alone is blocked.
Follow the checksWFW9620HW Dispenser 2: Detergent or Fabric Softener?
The one-liter second bulk dispenser can hold liquid HE detergent or liquid fabric softener, but its configured contents must match what you put in it.
Follow the checksWFW92HEFW Door Stays Locked While FanFresh Runs
The door remains locked while FanFresh is active.
Follow the checksWTW5000DW Soak Drains Without Spinning: Cycle or Fault?
On the documented WTW5000DW cycle guide, Soak ends by draining without spinning.
Follow the checksWFC7500VW A09: Check Water Supply Before the Drain System
A09 on WFC7500VW means no or insufficient incoming water.
Follow the checksWFW5620HW Clean Washer Reminder After 30 Washes
The flashing Clean Washer with affresh reminder is triggered after 30 wash cycles.
Follow the checksWhirlpool rL or F0 E1 With an Empty Drum
On the covered front-load platform, rL or F0 E1 means Clean Washer detected a load.
Follow the checksWhirlpool dET: Missing Cartridge or Intentional Single Dosing?
dET means the detergent dispenser cartridge is not detected.
Follow the checksWhirlpool Int After Cancel: Allow the Stop-and-Drain Interval
Int identifies a paused or canceled cycle on the covered front-load washers.
Follow the checksWhirlpool F0 E4 Even on Cold: Check the Supply Mapping
On the covered top-load platform, F0 E4 means the washer senses water that is too hot.
Follow the checksWhirlpool F5 E4 After You Already Opened the Door
Whirlpool defines front-load F5 E4 as three consecutive cycles without a door opening.
Follow the checksWhirlpool F8 E2 After Cleaning the Detergent Drawer
Front-load F8 E2 identifies a dispenser-system problem.
Follow the checksWhirlpool F0 E3 Returns After Reducing the Load
The covered top-load F0 E3 message identifies an overload condition and recovery handling.
Follow the checksWhirlpool F0 E5 on a Small Load: Size Is Not Balance
F0 E5 on the covered top-load washers means an unbalanced or oversized load.
Follow the checksWhirlpool 1h on the Display: Delay Wash or a Failed Start?
On covered front-load models, 1h through 12h identifies Delay Wash.
Follow the checksWhirlpool Err When Changing a Running Cycle
Whirlpool documents Err when a running cycle is changed or modified, or when a start is attempted with the door open.
Follow the checksWM6700HBA Refill Alarm With a Full Reservoir
A full tank and a continuing refill alert are not automatically evidence of a failed dispensing pump.
Follow the checksWM6700HBA: Using the Softener Tank for Detergent
This model can change its softener reservoir to a second detergent reservoir using Softener Tank Use.
Follow the checksWM6700HBA Nozzle Clean Is Different From Tub Clean
ezDispense Nozzle Clean targets the reservoir-connected dispensing hose.
Follow the checksWM6700HBA Dispenses Too Much: Set the Detergent Baseline
Use Default Det.
Follow the checksWM6700HBA Cycles Moved or Disappeared: Check the List Settings
Cycle Optimization can reorganize the WM6700HBA cycle list based on use.
Follow the checksWT7400CW Water Plus Changes Normal to Deep Wash
On the WT7400CW, selecting Normal with Water Plus changes the cycle to Deep Wash before it starts.
Follow the checksWT6105CW Bedding/Waterproof: Why Deep Fill Is Unavailable
The WT6105CW has a dedicated Bedding/Waterproof cycle.
Follow the checksWM3998HBA Dry Only Starts With a Spin: What to Select
Dry Only on the WM3998HBA is selected from the Dry control without choosing a wash cycle.
Follow the checksWM3998HBA Stays Damp: Check the Condensing Water Supply
The WM3998HBA is a conventional ventless condensing combo, not a stand-alone vented dryer.
Follow the checksWM4500HBA Powder Detergent: Use the Manual Path
WM4500HBA ezDispense reservoirs are for the specified liquid products, not powder.
Follow the checksWD100CW dE1, dE2 or dE3: Drawer Versus Lid
A WD100CW SideKick has a sliding drawer and an inner lid.
Follow the checksWD100CW Keeps Chiming Before Rinse: The Softener Alert
The WD100CW can chime repeatedly before the final rinse so liquid fabric softener can be added.
Follow the checksWM4200HWA Remote Start Stops Working After Opening the Door
The WM4200HWA manual states that a cycle cannot be started remotely after the door has been opened.
Follow the checksLG Washer PF Returns: Outage Recovery Versus Repeated Power Loss
PF identifies interrupted power.
Follow the checksLG Washer PE After a Reset: What the Water-Level Code Establishes
PE is a water-level sensing problem, not the same as IE slow filling.
Follow the checksLG Washer FE or Water Entering While Off: Stop the Fill First
FE reports overfilling on applicable LG washers.
Follow the checksLG Washer LE After a Heavy Load: Reduce the Strain Before Retrying
LE indicates that the tub cannot spin normally.
Follow the checksLG Washer tE Versus Cold Clothes After Sanitary
Cold clothes at the end of a heated wash do not establish a heating fault because rinsing may use cold water.
Follow the checksLG Washer SUD With No New Detergent: Check Residue and Auto Dosing
“No detergent added” does not prove there was no detergent in the wash.
Follow the checksLG Front-Load dE1 or dE2 With the Door Closed
dE1 concerns a door that is not properly closed; dE2 concerns a closed door that has not locked.
Follow the checksLG Washer vS, uS or u5: Sensor Code Versus UE
LG notes that vS can resemble uS or u5 on the display.
Follow the checksLG Top-Load dL With the Lid Closed: Inspect the Locking Area
dL is a locking problem on applicable LG top loaders.
Follow the checksLG Washer E6: A Visible Object Check Before Service
LG identifies E6 as a clutch-related error on the applicable washer family and advises checking for objects between the pulsator and tub.
Follow the checksLG Washer tcL After Tub Clean: Reminder, Interrupted Cycle or Another Code?
tcL is a Tub Clean reminder, not a temperature-sensor diagnosis.
Follow the checksLG Top-Load FF After Cold Weather: Identify the Frozen Path
FF is freeze detection on the LG top-load family covered by the guidance.
Follow the checksWF45R6100AW Spin Only: Avoid Starting Another Rinse
Hold Spin for three seconds to select Spin Only.
Follow the checksWF45R6100AW Child Lock Flashes: Temporary Off or Fully Off?
Use Temp.
Follow the checksWF45R6100AW Delay End: Why the Wash Does Not Start Immediately
Delay End schedules completion, rather than a delay before starting of the same length.
Follow the checksWF45T6000AW Self Clean Light Blinks After Washing
The Self Clean reminder appears after 40 wash cycles on the cited WF45T6000A manual.
Follow the checksWF45T6000AW Emergency Drain: Tube Before Pump Filter
The model has an emergency drain tube at the lower front access area.
Follow the checksWF50A8800AV Does Not Dispense on Delicates: Check Dose per Wash
Check Dose per Wash and Dose per Rinse after selecting the cycle.
Follow the checksWF50A8800AV Missing a Wash Cycle? Check My Cycles
The displayed cycle list can be personalized through My Cycles.
Follow the checksWF50A8800AV Calibration Is in System Functions
For the cited model, hold Options for three seconds, select Calibration with the Navigation dial and confirm with OK.
Follow the checksWA50R5400AW Waterjet Stops and Power Waits During Drain
Active Waterjet stops automatically after five minutes on the cited manual.
Follow the checksWF45K6500AV AddWash Will Not Open During a Hot Cycle
Pause only when the Add Wash indication permits adding laundry.
Follow the checksWF45A6400AW Door Stays Locked After a Cycle: Stay Connect
Check whether Stay Connect is active in SmartThings.
Follow the checksWV60M9900AV Upper Washer 1dC4: Inspect the Latch Button
On FlexWash, Samsung identifies a missing rubber button beside the upper washer latch as a cause of 1dC4.
Follow the checksWA55A7700AV Recall Software: Check the Remedy Before Washing
Check both model and serial number against the recall, then verify the installed software using Samsung’s current remedy instructions.
Follow the checksSamsung ddC or dC3 After Adding Laundry
ddC/dC3 concerns the Add Door, not a drain filter.
Follow the checksSamsung SDC/5DC With the Detergent Drawer Closed
SDC/5DC means the detergent drawer is not confirmed completely closed.
Follow the checksSamsung dn and Frozen Controls During an Update
dn is a software-download status.
Follow the checksSamsung CL After Opening the Lid: Why Water Drained
On covered newer washers, CL can identify a Child Lock protective drain after the lid or door was opened with an unsafe water level.
Follow the checksSamsung PC Versus PC1: Clutch Position or Signal?
PC/PE concerns clutch position; PC1/PE1 concerns the clutch Hall signal.
Follow the checksSamsung 3C With No Drum Rotation: What the Code Establishes
3C belongs to the motor-error family in Samsung’s reference.
Follow the checksSamsung AC6 After a Power Event: Preserve the Fault Details
AC6 is a communication error in Samsung’s code reference.
Follow the checksSamsung 8C After Moving: Sensor Fault or Ordinary Imbalance?
Samsung groups 8C with MEMS-sensor errors.
Follow the checksSamsung 9C1 After an Outage: Power Check Before Another Wash
Samsung groups 9C1/9C2 and PF with supply-voltage problems.
Follow the checksSamsung SUD With No Visible Foam: Record What Happens Next
SUD is an oversudsing indication, not a direct instruction to replace a sensor.
Follow the checksSamsung Washer LC With No Visible Leak: Do Not Assume It Is Dry
Samsung’s LC/LE/1C family can concern water level or leakage.
Follow the checksSamsung OC and Water Entering While Off: Stop the Supply
OC/OE is an overflow code family.
Follow the checksMHW5630HW Control Lock Will Not Clear: Watch the Countdown
Hold the Control Lock control continuously for three seconds.
Follow the checksMHW6630HW Door Locked After Washing: Check Fresh Hold
The MHW6630HW has a 16-hour Fresh Hold option.
Follow the checksMVW6230HW Deep Fill: Auto, Medium, High and Max Compared
MVW6230HW provides Auto, Medium, High and Max Fill choices.
Follow the checksMVW6500MW Pet Pro Filter Not Catching Hair
On the MVW6500MW, select Pet Pro and start with a clean filter.
Follow the checksMHW8630HW Optimal Dose: Detergent Settings Before Service
The MHW8630HW Optimal Dose system meters liquid HE detergent from a reservoir.
Follow the checksMaytag F9 E1 With a Clean Filter: Inspect the Drain Path
F9 E1 reports a long-drain problem.
Follow the checksMaytag Sd Keeps Adding Rinses: Let the Suds Routine Finish
On the covered Maytag front-load washers, Sd or Sud means excess suds.
Follow the checksMaytag Int and a Locked Door After Canceling
Int indicates a paused or canceled cycle.
Follow the checksMaytag rL or F0 E7 During Clean Washer: Remove the Load
Maytag documents rL/F34 and, on other supported platforms, F0 E7 as clothing detected during Clean Washer.
Follow the checksMaytag F0 E5 Returns After Redistributing the Load
F0 E5 means the load is unbalanced or too large on the covered top-load washers.
Follow the checksMaytag F5 E3 and a Lid That Will Not Unlock
Maytag identifies F5 E3 as a lock-related alert on covered top-load washers.
Follow the checksMaytag F7 E1: Identify the Washer Platform Before Parts
F7 E1 is a speed-related fault, but the relevant system depends on the washer platform.
Follow the checksMaytag F8 E6: Hot-Water Fault or Open Lid During Soak?
Maytag explicitly publishes two possible F8 E6 meanings depending on model: an open lid during soak, or no hot water detected.
Follow the checksMVWC465HW1 Deep Water Wash: Check the Water Level Knob
The MVWC465HW1 owner guide directs owners to the Water Level knob’s Deep Water Wash setting for more water.
Follow the checksMVW5430MW Fabric Softener: Select an Extra Rinse Setting
The MVW5430MW quick-start guide says to use one of the two topmost Soil & Rinse settings when using fabric softener; those settings add an Extra Rinse.
Follow the checksMVW7230HW Rinse and Spin: Use Drain & Spin Plus Extra Rinse
For a Rinse & Spin on MVW7230HW, the quick-reference guide says to select Drain & Spin, then select Extra Rinse.
Follow the checksMVWB765FW Clean Washer Was Interrupted: Rinse Before Laundry
The MVWB765FW guide says not to interrupt Clean Washer.
Follow the checks